Nissan Forum banner
1 - 10 of 10 Posts

· Ex-mod/nissan guru
Joined
·
2,348 Posts
Discussion Starter · #1 ·
Hi again !!... here my new problem... i transplanted a new engine in my B12... its a 93 e16 from a classic... every thing is plugued correctly.. every damn bolt as been screwed where they have to go... and still the car doesnt start... shit i hate this !!....

the head gasket as been changed by the guy at the junk yard...
i used my intake / exhaust manifold...
my distributor too...


theyre is fuel coming throu cylinder cuz its smell so bad....
theyre is fire at the spark plugs...
plugs is good shape too (gaped .035)
engine turning but doenst start....

timing belt must be set wrong ??????.... could it be ???

help me here !! :))) next time ill have some pix !!.. i took maybe 15pic of the transplant !!

Ciao !
 

· Ex-mod/nissan guru
Joined
·
2,348 Posts
Discussion Starter · #2 ·
also... the guy putted fuel inside the cylinder... si itwas backfiring (poping) a lot the first 5 minute i attempted starting it !! :)
 

· Ex-mod/nissan guru
Joined
·
2,348 Posts
Discussion Starter · #5 ·
allready tried that !!... not working... btw distributor cannot be put on wrong side... cuz the shaft (splined) is off center... you can put the cap wrong... inside it...welll... im gonna open up the timing belt tommorow...

anyone got something else ???
 

· Ex-mod/nissan guru
Joined
·
2,348 Posts
Discussion Starter · #6 ·
i just been told the classic from 93 as slight different engine called d16... ???... the same damn thing but with minor difference... like new comp, injection... but i told the guy i was using everything from the previus engine so he told me that is probably a timing issue... (timing belt..)

im gonna check if i got fire in same time that the #1 piston at tdc...
 

· Ex-mod/nissan guru
Joined
·
2,348 Posts
Discussion Starter · #10 ·
As i expected... timing wads off a tooth... but i cranked it !!... if fixed the timing belt and it started.... running real bad.. (exhaust is shut !.. cutted 3 place so.. can be minor there...)


So i went to my job with the car... after the shift, i start the car... like he was doing earlier (think the distrbutor choke a piston or maybe the bent valve thing :( ) i rev it up till 4000/4500... and just to see the power, i drop the clutch in 1st... retaining myself, i made a small burn but wath??? WTF!!!!!!!!!... clutch gone !!!... i can hear a rattling sound coming from underneat the car !!..... dont know wath it is... (pretty sure the clutch bearing gone trhou something)..... (stalled)....


Shit major problems always get on my tail !!! :(
 

· Ex-mod/nissan guru
Joined
·
2,348 Posts
Discussion Starter · #11 ·
Ricebox you also got a diferent cam gear... different (2 metal line vacuum instead of 3... ) the dealer told me you should have a different ecu and some other electronic goodies... wich i dont know about...

sure thing, : its the same engine... but different parts...

BlownB, well i dont know anything about this engine as it is..unless that its basically the good old E16i with (probably) different parts manufavturer...
 

· Ex-mod/nissan guru
Joined
·
2,348 Posts
Discussion Starter · #13 ·
i should have known better !! :(.... well maybe in the spring time... :)... now the cost is just getting up and up and up.... one of my firend told me that it is probably the clutch springs that must got off ... one way or another im towing the car tomorrow to my garage to get that darn thing repaired by the week end...


:)....


If it goes well maybe next summer vacation, im gonna get down to your house and we ll put it in togueter !! :) to would be soooooooo nice to work with you on my car !! :)
 

· Ex-mod/nissan guru
Joined
·
2,348 Posts
Discussion Starter · #17 ·
ok to close the thread.....



Finally my sentras back on the road... wasnt clutch related.... ive just badly installed a drive axle... (3/8 of an inch in the tranny)

so when i spinned it... the diff completely chewed the end of the spline... :(... good news... cost me 20$ to make it fix.. :) and trust me now ... its in his place... (20pounds mass to make it go there)


:) now need to adjust the engine so im sending it to the dealer monday... :) rough idlee... probably bad cap/rotor


youll get the pics tonight.. since i forgot the camera at my girlfriends home...


:)
 

· Ex-mod/nissan guru
Joined
·
2,348 Posts
Discussion Starter · #19 ·
average: i posted the pix in a thread called pix of the newer engine" in the b12 sections... not into this one !! :)
 
1 - 10 of 10 Posts
This is an older thread, you may not receive a response, and could be reviving an old thread. Please consider creating a new thread.
Top