Nissan Forum banner
1 - 20 of 24 Posts

·
Pimpin the BigDaddyMobile
Joined
·
486 Posts
Discussion Starter · #1 ·
hey i got a b14 and i know some have moved they HVAC to the buttom of the console

Where can I get some directions or a howto to do it?

I need to know like asap.

Thanks
 

·
G14 CLASSIFIED!!!!
Joined
·
763 Posts
Some one make this sticky!!!!!

FatBoy4 said:
hey i got a b14 and i know some have moved they HVAC to the buttom of the console

Where can I get some directions or a howto to do it?

I need to know like asap.

Thanks
-Take off the center top cap inbetween the hazard and rear window defroster with a Slotted screwdriver.
-Use a Phillips head to remove main screw.
-Gently Pull out from the top twords down to release clips On surrounding trim.
-Disconnect hazzard and rear window controls.
-Unscrew and disconect stereo and lower din brackets With Phillips screwdriver.
-Mark stereo brackets Below the stereo
-Use a Dremmal and cutting wheel and cutt off lower half of the stereo brackets.
-Unscrew Hvac unit with phillips head screwdriver.
-Twist and pull out to disconnect wires.
-Use Needle Nose plyers to Undo Small cable clips(Carefull can loose easily)
-Test fit Hvac unit in lower position Linned up with factory lower din screw holes. :Note Hvac sits 1" Futher out that stock mounting points.
-Mark Top Right corner of hvac unit were it catches and lower Left corner.
-Use a dremmal and sanding drum and remove area for a snug fit.
-TEST FIT!!! SAND A LITTLE!!!TEST FIT!!! SAND A LITTLE!!!TEST FIT!!! SAND A LITTLE!!!TEST FIT!!! SAND A LITTLE!!!TEST FIT!!! SAND A LITTLE!!!
-Rerun Hvac Cables to the assembly and connect wires.
-Once it has a snug fit 2 1 3/4" Metal screws Through The Front of the Hvac Mounting points.
-Place 1 1/2" Springs over Metal screws Behind hvac mounting points.(The springs will make up the 1" difference in mounting depth and securly hold it in place.)
-Line Hvac to the Lower Din factory mounting points with Spring and screws
inplace.
-Slowly screw into factory mounting points a little on each side till it sits flush with stereo.
-Connect and screw stereo in to stock location.
-Test fit trim.
-If Hvac sits out to far screw in some more till everything is flush.

Godd Luck and take your time....
 

·
Pimpin the BigDaddyMobile
Joined
·
486 Posts
Discussion Starter · #3 ·
yo we already tried but stoped when we found the cables.

Do we need to cut the cables and put an extension in em?

ScorchN200SX said:
-Take off the center top cap inbetween the hazard and rear window defroster with a Slotted screwdriver.
-Use a Phillips head to remove main screw.
-Gently Pull out from the top twords down to release clips On surrounding trim.
-Disconnect hazzard and rear window controls.
-Unscrew and disconect stereo and lower din brackets With Phillips screwdriver.
-Mark stereo brackets Below the stereo
-Use a Dremmal and cutting wheel and cutt off lower half of the stereo brackets.
-Unscrew Hvac unit with phillips head screwdriver.
-Twist and pull out to disconnect wires.
-Use Needle Nose plyers to Undo Small cable clips(Carefull can loose easily)
-Test fit Hvac unit in lower position Linned up with factory lower din screw holes. :Note Hvac sits 1" Futher out that stock mounting points.
-Mark Top Right corner of hvac unit were it catches and lower Left corner.
-Use a dremmal and sanding drum and remove area for a snug fit.
-TEST FIT!!! SAND A LITTLE!!!TEST FIT!!! SAND A LITTLE!!!TEST FIT!!! SAND A LITTLE!!!TEST FIT!!! SAND A LITTLE!!!TEST FIT!!! SAND A LITTLE!!!
-Rerun Hvac Cables to the assembly and connect wires.
-Once it has a snug fit 2 1 3/4" Metal screws Through The Front of the Hvac Mounting points.
-Place 1 1/2" Springs over Metal screws Behind hvac mounting points.(The springs will make up the 1" difference in mounting depth and securly hold it in place.)
-Line Hvac to the Lower Din factory mounting points with Spring and screws
inplace.
-Slowly screw into factory mounting points a little on each side till it sits flush with stereo.
-Connect and screw stereo in to stock location.
-Test fit trim.
-If Hvac sits out to far screw in some more till everything is flush.

Godd Luck and take your time....
 

·
Pimpin the BigDaddyMobile
Joined
·
486 Posts
Discussion Starter · #4 ·
We are gunna put the sterio in the top postition
till i get a dvd flip out
 

·
WHOOT!
Joined
·
1,286 Posts
yeah, i saw em once. you know this could've been adressed in the thread i started like a week ago asking this very same question.
(finally just pmed scorchN)

whoever finds the pics post em in this thread plz!
 

·
Pimpin the BigDaddyMobile
Joined
·
486 Posts
Discussion Starter · #10 ·
well i pmed him and he never answered


xt_out said:
yeah, i saw em once. you know this could've been adressed in the thread i started like a week ago asking this very same question.
(finally just pmed scorchN)

whoever finds the pics post em in this thread plz!
 

·
Pimpin the BigDaddyMobile
Joined
·
486 Posts
Discussion Starter · #11 ·
Do u have any pics of the conversion while in progress?
 

·
Pimpin the BigDaddyMobile
Joined
·
486 Posts
Discussion Starter · #12 ·
hey do u have any pics of the finished because we cant get the hvacs to be centered in the bottom
 

·
WHOOT!
Joined
·
1,286 Posts
leaver him alone guys :fluffy:
im sure mike is busy with his qr swap and his directions are as thorough as its gonna get.
im all for seein some pics when you get it done. any pics of how it fits now?
 

·
Pimpin the BigDaddyMobile
Joined
·
486 Posts
Discussion Starter · #14 ·
IT DONT FIT
IT TO FAR TO THE LEFT
i cant get it centered
 

·
Oh, Herro!
Joined
·
2,337 Posts
You should get in there and take some photos of how the HVAC is sitting in its new home. Fixing the problem may be as simple as grinding down one of the sides or re-drilling one of the mounting brackets.
 

·
Pimpin the BigDaddyMobile
Joined
·
486 Posts
Discussion Starter · #16 ·
i have grinding the sides
it gettin caught on the metal brace
 

·
I command you to SEARCH
Joined
·
2,748 Posts
here is a pic of the finished HVAC move...


 

·
Pimpin the BigDaddyMobile
Joined
·
486 Posts
Discussion Starter · #19 ·
why the hell can anyone else get it centered without cuting the metal peice but i cant?
 

·
Pimpin the BigDaddyMobile
Joined
·
486 Posts
Discussion Starter · #20 ·
i am going it alittle differently
I am moving my cd player to the very very top
and not leaving it in the middle.
 
1 - 20 of 24 Posts
Top