wont start

NegativeGain · Dec 21st, 2006, 07:58 PM

i just disconnected my hose attached to my IAA. My car was having high idol problems.So I looked around and found this site it talks about spraying WD-40 in the tube that goes to your air regulator.against what the site says i sprayed without the car being on.
heres the site Robo

now my car wont start. Any help would be appreciated

**Spongerider** · Dec 21st, 2006, 08:05 PM

Quote:

Originally Posted by NegativeGain

i just disconnected my hose attached to my IAA. My car was having high idol problems.So I looked around and found this site it talks about spraying WD-40 in the tube that goes to your air regulator.against what the site says i sprayed without the car being on.
heres the site Robo

now my car wont start. Any help would be appreciated

LoL!

Just spray some brake fuild in there and let it sit. Tomorrow it should be dry and reconnect to tube. Make sure the tube is not cracked.

So what exactly is your high idle problem doing? Give me detail?

NegativeGain · Dec 21st, 2006, 08:21 PM

well its just high it hovers around 900 to 1000 rpm just sitting.the hose is brand new just replaced it.

so sponge have you tried this on your Z

**Spongerider** · Dec 21st, 2006, 08:26 PM

Quote:

Originally Posted by NegativeGain

well its just high it hovers around 900 to 1000 rpm just sitting.the hose is brand new just replaced it.

so sponge have you tried this on your Z

My car always runs well.

When you do get your car running let it idle for about 10 minutes. If the idle does not go down then you most likely have a vacuum leak. Report back and I well tell you how the search for that leak?

NegativeGain · Dec 21st, 2006, 08:37 PM

will do good buddy if it ever starts LOL

Z_Rated · Dec 21st, 2006, 08:40 PM

I second a vacuum leak, first thought at least for high idle. Check balance tube connections. Z

NegativeGain · Dec 22nd, 2006, 09:21 AM

one day later and still it doesn't start i will tighten* the clamps today.but just loose clamps will cause my car not to start?

**Spongerider** · Dec 22nd, 2006, 12:35 PM

Quote:

Originally Posted by NegativeGain

one day later and still it doesn't start i will tighten* the clamps today.but just loose clamps will cause my car not to start?

Is the car turning or is the battery dead?

NegativeGain · Dec 22nd, 2006, 07:17 PM

the car turns just fine.so i did an ECU Diagnostic and got a code 21: Ignition Signal Circuit whats my next step peeps

NegativeGain · Dec 26th, 2006, 08:15 AM

would push starting the car work?

**Spongerider** · Dec 26th, 2006, 11:24 AM

Quote:

Originally Posted by NegativeGain

the car turns just fine.so i did an ECU Diagnostic and got a code 21: Ignition Signal Circuit whats my next step peeps

Sounds like you need to replace your ignition but try this first. Disconnect the battery and reconnect it a minute later and try and start it? Next try and see if the code comes up again. I would also look at your fusable links but that is a real guess.

NegativeGain · Dec 26th, 2006, 11:57 AM

so running starting it wouldnt work then.
i'll try disconnecting the battery.

how much would a new starter cost anyway?

**Spongerider** · Dec 26th, 2006, 12:37 PM

Quote:

Originally Posted by NegativeGain

so running starting it wouldnt work then.
i'll try disconnecting the battery.

how much would a new starter cost anyway?

Try COZ has good prices on OEM parts.

Nissan Performance Parts Aftermarket Parts Upgrades Accessories - 300zx 350z G35 240sx

If you don't see it then email him. Coz is good at replying back fast.

NegativeGain · Dec 26th, 2006, 02:10 PM

thanx sponge ima give it a run start after the battery is connected .

thanx peeps

NegativeGain · Jan 4th, 2007, 06:28 PM

so some how i ruined the my crank angle sensor and the ignition switch.

so now im learning my lesson by paying out of my pocket

thanks for the help people