G2-0-0SX

I searched but I guess i'm not too good at it cuz it kept comming up "no matches" I just need to know how long I need to bake my headlights at what tempurature in order to soften the glue that hold the lenses on. Also the same things for doing the corners, i'm working on a project, getting rid of my headlight covers. If anyone has a write up / how to type of thing for this that would be VERY helpful.

thanks alot eveyrone.

__________________
"SHIFT INTO AWESOME!! AND THEN SOME!" My lil black 200sx
[Rota's, Tein/AGX, catback, WAI, strut bars, custom gauges, xplod, short shifter, razo knob, smoked tails, stealth headlights/corners, grille, splitters, M3 mirrors, catch can, 20% tint, etc...]

 

sentra_hilo

im no sure how long but make sure its at a low heat. i made the mistake of melting my lenses. i think there were many posts of this before

holy200sx

15-20 minutes, at 200 degrees... the lense will come off, but you will have to use a flathead screwdriver to pry it off..

nissan_dude

to be safe i usually use a lower temperature (150-170ºF) for about 15 min for the headlights, 12 min for the corners...make sure u take the rubber hosing off b4 u start baking. i recommend using an old butter knife to pry it off since using the flathead screwdriver can damage the assembly/lens more easily..

and that glue holding the housign & lens together is very sticky and will stick to anything it touches so be careful when ur seperating it b/c u might get strands on the housing that are almost impossible to get out. save as much of it as possible and use some type of clear sealant (silicone?) when u put it back together (i used sum loctite stik&seal stuff,...dunno if this truly works but its better than nothing) so your headlights dont condensate inside

check this out for more info & writeups --> http://www.b14nissan.org/howto-agreed.html

__________________
13.9 @ 101mph on blizzaks
For Sale: stock avenir cams

G2-0-0SX

thanx guys!!

__________________
"SHIFT INTO AWESOME!! AND THEN SOME!" My lil black 200sx
[Rota's, Tein/AGX, catback, WAI, strut bars, custom gauges, xplod, short shifter, razo knob, smoked tails, stealth headlights/corners, grille, splitters, M3 mirrors, catch can, 20% tint, etc...]

 

Ninety-Nine SE-L

do it in 5 minute increments, 15 sounds too long 4 me

__________________
Site for my 99 SE-L|||Cardomain Page
LiuspeedTuning.com

andre

I agree with 1997GA16DE (thats a long name to type man )
I did mine in increments too, just pry it up a little at a time and pop it back in the oven.

__________________
Team Serious NYC
1.6L N/A.....sold
3.0L Z Turbo.....donated
75 280Z.....new project
Mazda 6......zooom zoom ;)

G2-0-0SX

finished the corners...look great...I did them in incriments too, I just kept pulling them up little by little, and heating and pulling till they came off. I'll do the headlights tommorow, maybe when my hand heals up a little bit and I can actually use it properly.

thanx for the help everyone.

__________________
"SHIFT INTO AWESOME!! AND THEN SOME!" My lil black 200sx
[Rota's, Tein/AGX, catback, WAI, strut bars, custom gauges, xplod, short shifter, razo knob, smoked tails, stealth headlights/corners, grille, splitters, M3 mirrors, catch can, 20% tint, etc...]