Texas200

I wanna put another exhaust cutout on the back bumper of my 98 se-r. I dont care about the performance issue. I wanna know what will do the job the cleanest and easiest. What works? Any HELPFUL info is appreciated!

__________________
HS CAI, HS Header, JWT S3's, JWT Clutch, JWT flywheel, Custom 2.5 exhaust piping w/ magnaflow, KYB AGX’s, ST rear Sway bar, SMC SS, ES bushing galore, #1 front STB etc., Rear STB, UR pullies

 

wes

I used a small metal cutting blade on a sawzall and sanded it down with some 80 grit and finished it off with some 240 grit. Looks factory.

__________________
www.NissanPerformanceMag.com
250+WHP GA16 Proudly sponsored by:
JWT
www.notnser.com

Texas200

Hey thanks wes! You wouldnt happen to have any pics of your exhaust cutouts do you? Thanks again!

__________________
HS CAI, HS Header, JWT S3's, JWT Clutch, JWT flywheel, Custom 2.5 exhaust piping w/ magnaflow, KYB AGX’s, ST rear Sway bar, SMC SS, ES bushing galore, #1 front STB etc., Rear STB, UR pullies

wes

I did not cut the rear bumper I cut the front for my intercooler. Same material though.

__________________
www.NissanPerformanceMag.com
250+WHP GA16 Proudly sponsored by:
JWT
www.notnser.com

1CLNB14

Some B14 rear bumpers came OEM with 2 cut outs.
I would go that route.

I'm sure a Rotozip/sawzall would do the job though.

__________________
Sean M.
"Can you feel it building? Devastation is on the way!"

 

dry

you could use a 95-97 sentra rear bumper... it already has 2 cut outs, looks like this

snkee200sx

correct me if i'm wrong but only the 95-97 b14 models came with 2 cutouts and 98-99 came with one cutout.

__________________
mods... I/H/E, rota slips 15's c/f hood and slammed to the ground JDM for life!!!

wes

This is correct.

__________________
www.NissanPerformanceMag.com
250+WHP GA16 Proudly sponsored by:
JWT
www.notnser.com

azkicker0027

those older rear bumpers are just asking for some duals, if i had one, tha'ts exactly what i'm going to do.

__________________
Naturally aspirated autocross car.............naturally.
http://members.cardomain.com/azkicker0027 And defending STF in the process.
http://www.200sxonline.com/community/

Texas200

Does anyone know what the little black box located behind the rear bummper, on the drivers side is? Im worried it might get in the way of my dual exhaust. Can I take it out? I noticed the box isnt on 95-97 model se-r's. What the hell is that thing?

__________________
HS CAI, HS Header, JWT S3's, JWT Clutch, JWT flywheel, Custom 2.5 exhaust piping w/ magnaflow, KYB AGX’s, ST rear Sway bar, SMC SS, ES bushing galore, #1 front STB etc., Rear STB, UR pullies

 

azkicker0027

if i'm not mistaken, that the carbon canister for the fuel tank vapors.

__________________
Naturally aspirated autocross car.............naturally.
http://members.cardomain.com/azkicker0027 And defending STF in the process.
http://www.200sxonline.com/community/

Texas200

So can I remove the thing? Why dont the earlier models have it? Will it affect emissions? Also, would it be bad to have an exhuast pipe runnin through there? Im not putting dual fart cans on my car, just pipes with nice tips.

__________________
HS CAI, HS Header, JWT S3's, JWT Clutch, JWT flywheel, Custom 2.5 exhaust piping w/ magnaflow, KYB AGX’s, ST rear Sway bar, SMC SS, ES bushing galore, #1 front STB etc., Rear STB, UR pullies