I'm interested in purchasing a remote for a 96 Maxima. The only place I've been able to find one is on E-Bay Motors. Sellers are getting approximately $20-$25 per remote. Some sell remotes with instructions , other claim you can get remote settings info. at Nissan Dealers or over the net.
Wanted to check with the real pros and learn from you whether I'm on right the right track or simply headed down a Yellow Brick Road.
The remotes being sold have the following ID's.
FCC ID: A269ZUA078
ISC: 700 K1359
I'm also in the market for a spoiler (Pearl White) and mud guards for my 96 Max. Any suggestions on where to shop?.
I am also looking for new remotes for my 96 maxima...If I can find one at a junk yard any ideas where I can get the instructions for reprogramming them? Other than e-bay?
Yeah...reprogramming them is available for free. I would like to ask first though...Do you know for certain your Max has an alarm available to it right now? Mine has the security light but doesn't have the stock alarm.
Quote:
Q: How do I reprogram the Keyless Remote?
A: Here's the procedure from the 1995 Factory Shop Manual
Replacing Remote Controller or Multi-Remote Control Unit (LCU05)
Enter the identity (ID) code manually when:
remote controller or multi-remote control unit LCU05 is replaced.
an additional remote controller is activated.
ID Code Entry Procedure
To enter the ID code, follow this procedure.
Entering "Setting mode":
(1) Close and lock all doors.
(2) Insert and remove the key from the ignition more than six times within 10 seconds. (The hazard warning lamp will then flash twice.) At this time, the original ID codes are eliminated.
ID code entry:
(3) Turn ignition key to "ACC" position.
(4) Push lock button on the new remote controller once (for example, if door is locked using the remote controller during this ID code entry enable state, a new ID code can be entered). At this time, the new ID code is entered. (The hazard warning lamp will then flash twice.)
Additional ID code entry
(5) If you need to activate additional remote controllers, unlock the driver's door, then lock again with door lock knob.
(6) Push lock button on the additional new remote controller once.
(7) This ID code entry enable state and setting mode remain until the driver's door is opened.
NOTE
If you need to activate more than two additional new remote controllers, repeat the procedure "Additional ID code entry" for each new remote controller.
If the same ID code that exists in the memory is input, the hazard warning lamps will flash twice but the entry will be ignored.
Entry of maximum four ID codes is allowed and any attempt to enter more will be ignored.
Any ID codes entered after termination of the "setting mode" will not be accepted. Additionally remote control signals will be inhibited when an ID code has not been entered during the "setting" mode.
__________________
HIS: '07 Mazda CX-7 Touring...20% tint all around
HERS: '06 Mazda 3s...tint/CAI/Mazda3 pedals
GONE: '99 Maxima...i/h/e/eibachs/b&m/17s
Yeah...reprogramming them is available for free. I would like to ask first though...Do you know for certain your Max has an alarm available to it right now? Mine has the security light but doesn't have the stock alarm.
hey i am new to the forum i read the advice on reprogramming the remote controls for the lock and unlock,the only thing how do i reprogram the trunk button and alarm button?
Hello I'm new to the forum.
My keyless remote is not working, I've tested it and changed the battery to a battery I know works and it fails to give out a signal. I'm planning to buy one from ebay, but when I test the reprogramming method the hazard lights do not flash.
I enter the car, lock all the doors (including the driver's door) insert my key into the ignition and then fully take it out 7 times in less than 10 secs. but nothing happens.
Any ideas?
I would guess a completely dead key fob thing... I have one too, and it's dead. Took it apart, checked it over, replaced battery, did everything, still dead.
I would guess a completely dead key fob thing... I have one too, and it's dead. Took it apart, checked it over, replaced battery, did everything, still dead.
Thanks for the reply, I've won a fob (keyless remote) on ebay, but I can't get my car to reprogramming mode. No matter how many times I lock the doors and put the key in the ignition chamber (in and completely out slowly within 10 secs) I still can't get the hazard lights to flash to confirm that I'm in reprogramming mode.
Yes I believe it is the stock alarm, the former owner had to "bang" the fob a couple times before it would work.
I guess he "banged" it too much
I found a post on another site where someone had the same problem of not being able to get into reprogramming mode, he reckons that by disconnecting the battery for a couple of hours and then reconnecting it he was able to get into reprogramming mode.
But that didn't work for me.
I know this is a question but when exactly does the 10 secs start? is from the driver's side door being locked or from the first time you put the key in the ignition chamber?
Last edited by avw : Jan 31st, 2008 at 04:21 AM.
Reason: more info
Remotes for 1995-1999 Maxima
question but when exactly does the 10 secs start? is from the driver's side door being locked or from the first time you put the key in the ignition chamber?
Linear Mode
